about an hour and 25 minutes from the shop, east on US-2 through Ray
Insulation services in Stanley, ND
Williston Insulation provides insulation services for Stanley, ND, the Mountrail County seat, about an hour and 25 minutes east of our shop on US-2. Stanley is the far end of our service area, and we are open about what that means for scheduling. We handle spray foam, blown-in attic insulation, batts, rigid board, air sealing, and removal for houses, shops, and ag buildings. Drew Niskanen quotes and installs the work himself.
Stanley's houses, old and new
Stanley sits where US-2 meets ND-8, and like the other towns on the corridor it has two clear generations of housing. The older one runs from the 1950s through the 1970s: modest houses with 2x4 walls, shallow attic insulation that has settled over the decades, and basements with uninsulated rim joists. The newer one came with the Bakken activity of the 2010s, when Stanley added houses, townhomes, and apartments quickly.
For the older houses the job is usually attic air sealing and a blown-in top-up toward the R-60 ceiling minimum, plus closed-cell foam at the rim joist. For the newer ones, we start by checking the spots that fast construction tends to miss: the rim joist, the attic hatch, and the wall between the house and the attached garage.
Prairie wind and the cold side of a house
Stanley is on open prairie, and the wind from the northwest is a fact of life for half the year. Wind pushes air through every gap, and that moving air is what makes an under-insulated house feel colder than its R-value suggests. We treat air sealing as the first job on nearly every Stanley house, because adding insulation over leaks just hides them.
The farm and shop buildings around Stanley have the same issue with steel siding laps and roof fasteners. Heated shops that were built as cold shells sweat in winter. Closed-cell foam against the steel stops the condensation and seals the building in one pass.
How we schedule the drive to Stanley
Stanley is a real trip from Williston, most of an hour and a half each way. We do not pretend otherwise. Larger jobs (a whole house, a shop, a new build) are worth a dedicated day or more, and we schedule them that way. Smaller jobs we group with Ray and Tioga work along US-2 so that nobody pays for a trip that is mostly driving. When you send a quote request, tell us what the job is and we will be straight with you about whether it makes sense on its own or is better grouped.
Spray foam in Stanley
Spray foam in Stanley is mostly about rim joists and shops. The 1950s to 1970s houses get two inches of closed-cell at the rim, where it seals and insulates a spot batts cannot handle well. The heated steel and post-frame shops around town get foam against the metal to stop condensation. Attics get blown-in fiberglass. We describe how we choose on the spray foam insulation page.
What we install in Stanley
Crawl Spaces & Rim Joists
Closed-cell foam on the rim joist and crawl space walls, with a ground vapor barrier, to fix the cold floors and drafts almost every older Williston house has.
Pole Barns & Shops
Closed-cell foam sprayed direct to the steel skin of post-frame barns and shops, stopping the condensation drip and making the building cheap to heat.
New Construction
Foam scheduled into the build: rim joists, roof decks, and flash-and-batt walls sprayed after mechanicals and before drywall, ready for the insulation inspection.
Blown-In Attic Insulation
Loose-fill fiberglass or cellulose blown to the Climate Zone 7 target of R-60, with the top plates sealed and the eaves baffled before the first bag goes in.
Questions from Stanley
Is Stanley too far for you to take a small job?
Not too far, but small jobs in Stanley get grouped with other work along US-2 rather than scheduled as their own trip. That can mean waiting a bit for a date. If you have a larger job, or several small ones at the same property, it is easier to justify a dedicated day. We tell you which way it falls when we quote.
How does the distance affect the quote for Stanley?
We do not bury a trip charge in the number. If the drive changes the quote, we show it as its own line so you can see it. For larger jobs the drive is a small part of the total. For a very small job it can matter more, which is why we suggest grouping those with other work in the area.
Do you insulate new construction in Stanley?
Yes. New houses and shops in Stanley are a good fit for a dedicated trip because the work takes a full day or more. We work with the builder on sequencing, and we will recommend the assembly that fits the building, which is often batts or blown-in for walls and attics with closed-cell foam at the rim joist and any slab edge or crawl space.
We work in Stanley from our shop at 1926 44th St W in Williston, about an hour and 25 minutes away. There is no office in Stanley; we come to you. Nearby: Ray, ND, Tioga, ND.
Get a quote in Stanley, ND
Send the basics and an owner comes back with a straight answer on what it needs, what it doesn't, and what it costs.